Zitat:v1.2
- Added: Full support for Corona v2 (4GB Corona)
- Added: Auto Detect which mode to run in (it’ll autodetect if you are running on a MMC type of machine or a RAW type [MMC type = Corona 4GB/V2, RAW = any other older machine])
- Added: Safe-Flash (Read to recovery.bin then write)
- Added: Autoshutdown after flash (it’ll tell you it’s shutting down then count down starting at 5 seconds…)
- Added: It’ll turn off your wireless controllers during flash to keep you safe (if you reconnect them they’ll be shut off again while it’s working)
- Fixed: If you accidently hit eject the app now stays running!
- Fixed: You no longer see the options to write if you don’t have a updflash.bin next to the app…
- Fixed: Lot’s of code cleanup, making it look nicer and easier to follow/understand
- Added: It’ll now also check for Spare data before writing, again it’s a safety measure, if it finds spare data while in MMC mode it’ll warn you about it and give you the option to exit… and of course the other way around for raw mode…
- Added: The above check for spare also checks for the « Magic bytes » (your Xbox 360 image should start with 0xFF4F, i’ve never seen an image that differ from this, and thus it’s an easy way for me to check that the file you give the app really is a nand…)
- Fixed: The app will now clear the line of output before it starts overwriting, this means that you’ll no longer see leftover output on screen from previous output (mostly for error messages during progress output)
- Changed: The app now use a different font (it used Arial before, now it uses verdana)

Zitat:Build 280
Added Corona Install Images
Added DIY Corona xsvf for 48MHZ Osc
Added Monitor COM wiring Images
Added Enable/Disable of File Checks/Downloads in Settings
Added app re-opens in same screen position as was last used
Changed Use of registry for settings (values are stored elsewhere)
Changed Settings layout
Changed Custom Functions layout
Changed Xsvf selection screen
Fixed Nand init after dash selection
Fixed Cpukeydb clipboard after a sort-by selection
Fixed RGH auto Selection for Trinity
Fixed Small bug in dashlaunch selection radio buttons
Fixed Bug where crash occurs if filepath no longer exists for working folder
Tidied up Images dropdown menus
Added warning of existing files in output folder on start
Added fcrt when extracting files
Fixed bug in Scan for keys

Zitat: Simple 360 NAND Flasher By Swizzy***********************************
****************
* Requirements *
****************
- A Hacked Xbox 360 (JTAG/RGH or similar)
- A nand dump to write
****************
* What it does *
****************
- It’ll flash your motherboards nand with the supplied image using rawflash v4
***********
* Credits *
***********
- cOz Thanks for all the help you constantly give me with just about everything, and thanks for rawflash!
- Thanks also goes to who ever it was that ported rawflash to SDK in the first place and making it open source!

Zitat: TingedAce released a new version of XNand Healer GUI – a GUI app to
help you dump and manage NAND files, remap bad blocks and also uncripple
your Xbox 360.

What’s new/fixed (since v0.71):

- This release is for small but important change to the build glitch
image feature. It’s possible for another Multibuilder operation e.g.
“build JTAG image with custom smc” to leave an smc.bin file in the
datamy360 folder. The next time xeBuild is invoked by Xnandhealer (or
from cmd line) the build would erroneously pick up this smc and cause a
bad image build.

Now any leftover smc.bin file that may be present in the Datamy360
folder will be removed before building the image, thus ensuring the
correct smc is always used.

- Supports xeBuild 14699 and Multibuilder 0.6 (old ggBuild now not supported)

- Supports automatic XeLL bad block remapping in first 0×50 blocks (first 0×10 big blocks)

- Added option for including dashlaunch patches or not

- Added ‘Glitchable’ CB check (as well as JTAGable check)

- Added convenient button to open windows explorer at the working directory

- Updated known CB list with non-glitchable CBs 4577, 5772 & 6752

- Changed: USB is now the default interface instead of LPT

- Changed: Now uses xell image + other files from Multibuilder folder and removed embedded versions

- Changed: Removed in-built fcrt extractor (xeBuild does it now) Fixed:
Unable to select Jasp16 SB or BB in Build XeLL tab or Build Glitch tab

- Fixed: Relocated bad blocks could be reported in reverse order in a very few cases

Zitat:TingedAce released a new version of XNand Healer GUI – an app that started off as an uncrippling tool but now morphed into a general purpose NAND dumping tool that should really aid the first part of the JTAG’ing process.

What’s new/fixed:
* Big Block analysis and fixing now supported
* Now have the choice to fix NAND either from actual NAND or a virtual nand (image file)
* Added “CB” readout and exploitable indicator
* Added partial NAND analysis – can analyze images even if they don’t start at block 0
* Added Absolute and Relative addressing in the Hex Viewer (to accompany partial NAND analysis)

Requires Nandpro 2.0 (b/d or e) and FindSecData 0.62